SparkFun DIGI X-ON™ Kit for LoRaWAN®
SparkFun DIGI X-ON™ Kit for LoRaWAN® includes all that designers need to get an IoT system up and running within minutes. The kit incorporates a DIGI HX15 Gateway, an innovative SparkFun IoT node for the LoRaWAN board, and a dual-action SparkFun ENS160/BME280 (Qwiic) environmental combo board. The SparkFun DIGI X-ON Kit implements an easy and quick setup and connection of a LoRaWAN-based IoT Device that is usually convoluted and requires configuration-intensive effort. The kit also features a free 30-day DIGI X-ON device management platform subscription and cellular connectivity.
Features
- 16MB of flash
- 8MB PSRAM
- Qwiic connector
- On-board Lithium Ion (LiPo) battery charging
- Fuel gauge circuits
- microSD card
- Variety of IO pins
- RGB LED and user button
Specifications
- DIGI HX15 Gateway for LoRaWAN (EU)
- EU Interfaces
- RJ-45, 10M/100M/1000M Ethernet backhaul
- Cellular Backhaul - LTE Cat 1 or Cat M1/NB-IoT multi-region, up to 10Mbps, with 2G fallback for EU
- Supported bands LTE of B1, B3, B7, B8, B20, B28A; 3G: B1, B8; 2G: B3, B8
- LTE SIM - micro SIM (3FF), pre-activated SIM card included on LTE gateways
- LTE, 3G, 2G,3G (SMA type), omnidirectional, 50Ω, max. input 25W cellular antennas
- LoRa Specs
- EU868 regional bands
- +27dBm max TX power
- -138dBm RX sensitivity
- 8Rx / 1Tx channels
- -1.6dBm (SMA type), 50Ω, omni-directional, max. input 25W LORA antenna
- EU Interfaces
- DIGI HX15 Gateway for LoRaWAN (US)
- US Interfaces
- RJ-45, 10M/100M/1000M Ethernet backhaul
- Cellular Backhaul - LTE Cat 1 or Cat M1/NB-IoT multi-region, up to 10Mbps, with 2G fallback for EU
- Supported bands LTE of B2, B4, B12; 3G: B2, B4, B5
- LTE SIM - micro SIM (3FF), pre-activated SIM card included on LTE gateways
- LTE, 3G, 2G,3G (SMA type), omnidirectional, 50Ω, max. input 25W cellular antennas
- LoRa Specs
- US915 regional bands
- +27dBm max TX power
- -138dBm RX sensitivity
- 8Rx / 1Tx channels
- -1.7dBm (SMA type), omnidirectional, 50Ω, max. input 25W LORA antenna
- US Interfaces
- SparkFun IoT Node for LoRaWAN
- Raspberry Pi Foundation's RP2350A Microcontroller
- 15 Multifunctional GPIO Pins
- Up to eight 2-channel PWMs
- Up to two UARTs
- Up to two I2C buses
- Up to two SPI buses
- External memory
- 16MB QSPI Flash memory
- 8MB PSRAM memory
- DIGI's XBee® LR module
- LoRaWAN transceiver
- Modular certifications for FCC and IC
- Frequency range of SM 902MHz to 928MHz, 868MHz to 870MHz
- General features
- 83mm x 59mm dimensions
- USB-C® connectors
- USB 1.1 host/device support
- XBLR
- 2-pin JST connector for LiPo battery (not included)
- 4-pin Qwiic connector
- LiPo charger MCP73831 charger management controller at 500mA charge rate
- MAX17048 LiPo fuel gauge
- XBLR/UART selection switch
- Raspberry Pi Foundation's RP2350A Microcontroller
- SparkFun Environmental Combo Breakout ENS160/BME280 (Qwiic)
- 2x Qwiic-enabled connectors
- Input voltage range of typically 3.3V via Qwiic cable
- ENS160
- I2C addresses of 0x53 (default) or 0x52
- Wide operating ranges
- 1.71V to 1.98V VDD
- 1.71V to 3.6V VDDIO
- -40°C to +85°C temperature
- 5% to 95% (non-condensing) humidity
- IAQ standard compliance for AQI, eCO2, and TVOC
- Air Quality Index - Umweltbundesamt (AQI-UBA)
- 1 to 5 range
- 1 resolution
- Equivalent Carbon Dioxide (eCO2)
- 400ppm to 65,000ppm range
- 1ppm resolution
- Total Volatile Organic Compound (TVOC)
- 0ppb to 65,000ppb range
- 1ppb resolution
- Air Quality Index - Umweltbundesamt (AQI-UBA)
- Immunity to humidity and ozone
- Superior output stability over the whole temperature and relative humidity operating ranges
- Effective ozone compensation
- Independent sensor heater control for highest VOC selectivity and outstanding background discrimination
- BME280
- 1.71V to 3.6V VDD
- 1.2V to 3.6V VDDIO
- I2C addresses of 0x77 (default) or 0x76
- Temperature
- -40°C to +85°C operating range
- Full accuracy to ± 0.5°C from -0°C to 65°C
- 0.01°C resolution
- Humidity
- 0% to 100% RH operating range
- Accurate to ±3% from 20% -80% RH
- 0.008%RH resolution
- Pressure
- 30,000 Pa to 110,000Pa operating range
- Absolute accuracy of ±100Pa
- Relative accuracy of ±12Pa
- 0.18Pa resolution
- Altitude range
- 0ft to 30,000ft (9.2km)
- Relative accuracy of 3.3ft (1m) at sea level, 6.6 (2m) at 30,000ft
- Power LED
- 1.8V AP2127K voltage regulator (for ENS160)
- 2.2kΩ pull-up resistors
- Jumpers
- Power LED
- I2C pull-up resistors
- 0x53 (Default) or 0x52 selectable addresses
Kit Contents
- IoT node for LoRaWAN board
- Dual-action ENS160/BME280 (Qwiic) environmental combo board
Videos
IoT Node for LoRaWAN Board
ENS160/BME280 Qwiic Breakout
Associated Gateways
Digi Puertas de enlace LoRaWAN™ HX15
Designed for indoor IoT coverage, supporting various LoRaWAN channel plans.
Boards
SparkFun Qwiic Breakout Boards
Breakout Boards featuring sensors, actuators, and more, compatible with the Quiic Connect ecosystem.
Raspberry Pi Pico 2
Powered by the RP235x microcontroller platform designed by Pi.
SparkFun IoT Node for LoRaWAN®
Offers high usability to designers to set up a LoRaWAN-based IoT device.
Associated Modules
Digi XBee® LR LoRaWAN® Modules
Offer wireless communication that OEMs can easily integrate into end-node sensor products.
Publicado: 2025-02-01
| Actualizado: 2025-04-18